Tides Marine SURESEAL 7/8
Tides Marine SURESEAL 7/8" SureSeal Drip Free Self Aligning Propeller Shaft Seal for a 7/8 Inch Propeller Shaft

The Minimum Distance required from the end of the stern tube to the coupling is 7 1/4 Inches. Water from Raw Water Feed to SureSeal that delivers a minimum of 1 Gallon per Minute at Engine Idle Speed and increases as you throttle up, at a minimum of 2 psi. Features: ABS and Lloyds Type Approval. Minimal scheduled maintenance Replaceable Lip Seal while in the water (with Spare Seal Carrier Installed). No Winterization is necessary but winterization fluids will NOT harm the SureSeal. Easy to Install. HOUSING Made from fiber-reinforced composite material, the housing is strong, durable and compact. The SureSeal® is dimensionally unaffected by temperature and will not absorb water.  BEARING The integral PTFE bearing extends the operating life of the SureSeal® under normal operating conditions. HOSE Connecting the SureSeal® to the vessel is now easier with an “articulating hose”. This hose design automatically positions the SureSeal® the correct operating distance from the stern tube. No measurements are required – installation is simplified. The articulating hose reduces side loads to the SureSeal® when shaft misalignment occurs. As a result, lip seal and bearing life are extended. LIP SEAL REPLACEMENT The SureSeal® design incorporates a removable front cap which improves access to the lip seal. A worn lip seal can be replaced, even while the vessel is in the water, restoring the "100% watertight" characteristic of the SureSeal®. INJECTION FITTING The SureSeal water injection fitting is made from 316 stainless steel. Depending on the propeller shaft size, it comes in 3/8 or 1/2 inch sizes. A plastic cap is provided with each fitting so that if the injection hose has to be removed, the cap will restrict water flow into the vessel.

Add to Compare
Tides Marine SURESEAL 1 1/4
Tides Marine SURESEAL 1 1/4" - SureSeal Drip Free Self Aligning Propeller Shaft Seal for a 1 1/4 Inch Propeller Shaft

The Minimum Distance required from the end of the stern tube to the coupling is 7 1/4 Inches. Water from Raw Water Feed to SureSeal that delivers a minimum of 1 Gallon per Minute at Engine Idle Speed and increases as you throttle up, at a minimum of 2 psi. Features: ABS and Lloyds Type Approval. Minimal scheduled maintenance Replaceable Lip Seal while in the water (with Spare Seal Carrier Installed). No Winterization is necessary but winterization fluids will NOT harm the SureSeal. Easy to Install. HOUSING Made from fiber-reinforced composite material, the housing is strong, durable and compact. The SureSeal® is dimensionally unaffected by temperature and will not absorb water.  BEARING The integral PTFE bearing extends the operating life of the SureSeal® under normal operating conditions. HOSE Connecting the SureSeal® to the vessel is now easier with an “articulating hose”. This hose design automatically positions the SureSeal® the correct operating distance from the stern tube. No measurements are required – installation is simplified. The articulating hose reduces side loads to the SureSeal® when shaft misalignment occurs. As a result, lip seal and bearing life are extended. LIP SEAL REPLACEMENT The SureSeal® design incorporates a removable front cap which improves access to the lip seal. A worn lip seal can be replaced, even while the vessel is in the water, restoring the "100% watertight" characteristic of the SureSeal®. INJECTION FITTING The SureSeal water injection fitting is made from 316 stainless steel. Depending on the propeller shaft size, it comes in 3/8 or 1/2 inch sizes. A plastic cap is provided with each fitting so that if the injection hose has to be removed, the cap will restrict water flow into the vessel.

Add to Compare
Tides Marine SURESEAL 1 1/8
Tides Marine SURESEAL 1 1/8" - SureSeal Drip Free Self Aligning Propeller Shaft Seal for a 1 1/8 Inch Propeller Shaft

The Minimum Distance required from the end of the stern tube to the coupling is 7 1/4 Inches. Water from Raw Water Feed to SureSeal that delivers a minimum of 1 Gallon per Minute at Engine Idle Speed and increases as you throttle up, at a minimum of 2 psi. Features: ABS and Lloyds Type Approval. Minimal scheduled maintenance Replaceable Lip Seal while in the water (with Spare Seal Carrier Installed). No Winterization is necessary but winterization fluids will NOT harm the SureSeal. Easy to Install. HOUSING Made from fiber-reinforced composite material, the housing is strong, durable and compact. The SureSeal® is dimensionally unaffected by temperature and will not absorb water.  BEARING The integral PTFE bearing extends the operating life of the SureSeal® under normal operating conditions. HOSE Connecting the SureSeal® to the vessel is now easier with an “articulating hose”. This hose design automatically positions the SureSeal® the correct operating distance from the stern tube. No measurements are required – installation is simplified. The articulating hose reduces side loads to the SureSeal® when shaft misalignment occurs. As a result, lip seal and bearing life are extended. LIP SEAL REPLACEMENT The SureSeal® design incorporates a removable front cap which improves access to the lip seal. A worn lip seal can be replaced, even while the vessel is in the water, restoring the "100% watertight" characteristic of the SureSeal®. INJECTION FITTING The SureSeal water injection fitting is made from 316 stainless steel. Depending on the propeller shaft size, it comes in 3/8 or 1/2 inch sizes. A plastic cap is provided with each fitting so that if the injection hose has to be removed, the cap will restrict water flow into the vessel.

Add to Compare
Tides Marine SURESEAL 1
Tides Marine SURESEAL 1" - SureSeal Drip Free Self Aligning Propeller Shaft Seal for a 1 Inch Propeller Shaft

The Minimum Distance required from the end of the stern tube to the coupling is 7 1/4 Inches. Water from Raw Water Feed to SureSeal that delivers a minimum of 1 Gallon per Minute at Engine Idle Speed and increases as you throttle up, at a minimum of 2 psi. Features: ABS and Lloyds Type Approval. Minimal scheduled maintenance Replaceable Lip Seal while in the water (with Spare Seal Carrier Installed). No Winterization is necessary but winterization fluids will NOT harm the SureSeal. Easy to Install. HOUSING Made from fiber-reinforced composite material, the housing is strong, durable and compact. The SureSeal® is dimensionally unaffected by temperature and will not absorb water.  BEARING The integral PTFE bearing extends the operating life of the SureSeal® under normal operating conditions. HOSE Connecting the SureSeal® to the vessel is now easier with an “articulating hose”. This hose design automatically positions the SureSeal® the correct operating distance from the stern tube. No measurements are required – installation is simplified. The articulating hose reduces side loads to the SureSeal® when shaft misalignment occurs. As a result, lip seal and bearing life are extended. LIP SEAL REPLACEMENT The SureSeal® design incorporates a removable front cap which improves access to the lip seal. A worn lip seal can be replaced, even while the vessel is in the water, restoring the "100% watertight" characteristic of the SureSeal®. INJECTION FITTING The SureSeal water injection fitting is made from 316 stainless steel. Depending on the propeller shaft size, it comes in 3/8 or 1/2 inch sizes. A plastic cap is provided with each fitting so that if the injection hose has to be removed, the cap will restrict water flow into the vessel.

Add to Compare
Tides Marine SURESEAL 1 3/8
Tides Marine SURESEAL 1 3/8" - SureSeal Drip Free Self Aligning Propeller Shaft Seal for a 1 3/8 Inch Propeller Shaft

The Minimum Distance required from the end of the stern tube to the coupling is 7 1/4 Inches. Water from Raw Water Feed to SureSeal that delivers a minimum of 1 Gallon per Minute at Engine Idle Speed and increases as you throttle up, at a minimum of 2 psi. Features: ABS and Lloyds Type Approval. Minimal scheduled maintenance Replaceable Lip Seal while in the water (with Spare Seal Carrier Installed). No Winterization is necessary but winterization fluids will NOT harm the SureSeal. Easy to Install. HOUSING Made from fiber-reinforced composite material, the housing is strong, durable and compact. The SureSeal® is dimensionally unaffected by temperature and will not absorb water.  BEARING The integral PTFE bearing extends the operating life of the SureSeal® under normal operating conditions. HOSE Connecting the SureSeal® to the vessel is now easier with an “articulating hose”. This hose design automatically positions the SureSeal® the correct operating distance from the stern tube. No measurements are required – installation is simplified. The articulating hose reduces side loads to the SureSeal® when shaft misalignment occurs. As a result, lip seal and bearing life are extended. LIP SEAL REPLACEMENT The SureSeal® design incorporates a removable front cap which improves access to the lip seal. A worn lip seal can be replaced, even while the vessel is in the water, restoring the "100% watertight" characteristic of the SureSeal®. INJECTION FITTING The SureSeal water injection fitting is made from 316 stainless steel. Depending on the propeller shaft size, it comes in 3/8 or 1/2 inch sizes. A plastic cap is provided with each fitting so that if the injection hose has to be removed, the cap will restrict water flow into the vessel.

Add to Compare

Browse Marine Bearings & Seals

vfd